This post following next relating to How to Install a Bathtub is highly remarkable. Give it a go and make your own personal conclusions.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably tough project. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task and fit trying it. As opposed to employing a professional to take control of a halfway-completed job, it is better to consider utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will help you mount a new bathtub in your restroom if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also material checklist need to make up the following:
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub until the level reviews degree.
To set up faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bathtub has actually been used at least when as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that piece was really useful. Enjoyed our review? Please share it. Help another person locate it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Recurring Service Plans